LINE IMPEDANCE STABILIZATION NETWORKS / ARTIFICIAL NETWORKS
Do you need LISNs for your conducted emission test systems? Do you need ANs for your transients immunity or emissions test setups? We are offering CISPR 16, CISPR 25, CISPR 14-1, CISPR 15, CISPR 32, and ISO 7637-2 compliant LISNs, Artificial Networks (ANs). Fulfil your conducted emission, transient emissions, transient immunity and EMC requirements with the standard compliant line impesance stabilization networks and aritifical networks. Add remote control option to integrate it to your existing EMI Receiver. We are delivering LISNs and ANs to your address in 6 weeks (delivery time for some items vary)
Contact us and get your quote:
Conducted Emissions test systems include a set of instruments and software:
1. EMI Receiver
2. LISN
3. RF Cable
4. Current Probe (for power and data lines)
5. Test Software (embedded or remote)
LISNs are used between the device under test (DUT)/equipment under test (EUT) and EMI Receiver. They are for accurate EMI measurements of tested product.
What we offer?
We are offering CISPR 16, CISPR 25, CISPR 32, CISPR 14-1, CISPR 15, and ISO 7637-2 compliant artificial networks, line impedance stabilization networks and artificial mains networks.
How to choose right model?
Choose any model that fits your application by taking into account current and voltage limitations. Our LISNs / ANs can go up to 800 Amperes per line, 1500 V DC and 750V AC. Number of paths or lines are also essential. You can see these parameters on model names and descriptions of our LISNs / ANs. For instance, LIN100-1A is a single line (path) LISN.
How to order LISN/AN from Testups?
1. Choose any model listed on this page
2. Contact us with your billing, shipment and payment option details
3. Get your quote, pro-forma invoice or online payment link
4. Pay online by credit card or offline by bank/wire transfer
5. Get your invoice, shipment documents and tracking number of your shipment
Buy this LISN (9kHz-30MHz, CISPR16, 16Ax2 Path) online
CISPR 25 LISN (800 A, 1500 V DC)
AC: 750V, 50/60Hz- Automotive CISPR 25
- 800A x 1 Path
- Voltage limits: AC: 750V, 50/60Hz and DC: 1500V
- Frequency range: 100 kHz – 150 MHz
- AMN impedance: (5 μH + 1 Ω) || 50 Ω ± 10%
- Sutaible for BCI with external dummy load
CISPR 25 LISN (800 A, 600V DC)
AC: 300V, 50/60Hz- Automotive CISPR 25
- 800A x 1 Path
- Voltage limits: AC: 300V, 50/60Hz and DC: 600V
- AMN impedance: (5 μH + 1 Ω) || 50 Ω ± 10%
- Switchable 1uF capacitor
- Compatible for BCI testing
CISPR 25 LISN (200A, 600V DC)
AC: 300V, 50/60Hz- Automotive CISPR 25
- 200A x 1 Path
- Voltage limits: AC: 300V, 50/60Hz and DC: 600V
- AMN impedance: (5 μH + 1 Ω) || 50 Ω ± 10%
- Switchable 1uF capacitor
- Compatible for BCI testing
PRICE LIST
Price List shows the prices of Line Impedance Stablization Networks (LISNs) or Artificial Networks (ANs) we sell. You can order any of the listed items.
Lead time: 9-12 weeks (lead time of some models vary, you will see exact lead time of the LISN you ask on your quotation)
Shipment note: The shipping costs are excluded, we can either ship by using your shipment account or via our DHL account. If you want us to ship via our DHL account, please get an offer including shipment fees. When contacting us, please share your billing and shipping details.
| Model No | Description |
| LIN10-2 | CISPR 16, 10Ax2 Path, 9 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, 250 μH pre filter |
| LIN16-2 | CISPR 16, 16Ax2 Path, 9 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, 250 μH pre filter |
| LIN16-4 | CISPR 16, 16Ax4 Path, 9 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, 250 μH pre filter |
| LIN32-2 | CISPR 16, 32Ax2 Path9 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, 250 μH pre filter |
| LIN32-4 | CISPR 16 32Ax4 Path9 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, 250 μH pre filter |
| LIN63-2 | CISPR 16 63Ax2 Path9 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, 250 μH pre filter |
| LIN63-4 | CISPR 16 63Ax4 Path9 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, 250 μH pre filter |
| LIN100-2 | CISPR 16 100Ax2 Path(9) 150 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, (250 μH pre filter optional) |
| LIN100-2-option | 250uH choke for LIN100-2 for band A (9kHz to 150kHz) |
| LIN100-4 | CISPR16 100Ax4 Path9 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, 250 μH pre filter |
| LIN200-2 | CISPR16 200Ax2 Path(9) 150 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm, (250 μH pre filter optional) |
| LIN200-2-option | 250uH choke for LIN200-2 for band A (9kHz to 150kHz) |
| LIN200-4 | CISPR 16, 200Ax4, Path(9) 150kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm |
| LIN400-4 | CISPR 16, 400Ax4, Path(9) 150 kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm |
| LIN25-1M | MIL, 25Ax1 Path, (9 kHz) 150kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm |
| LIN100-1M | MIL, 100Ax1 Path, (9) 150kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm |
| LIN200-1M | MIL, 200Ax1 Path, (9) 150kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm |
| LIN400-1M | MIL, 400Ax1 Path, (9) 150kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm |
| LIN1500-1M | MIL, 1500Ax1 Path, (9) 150kHz – 30 MHz, 50 μH + 5 Ohm || 50 Ohm |
| LIN50-1A | Automotive CISPR 25 50Ax1 Path (5μH + 1 Ohm) || 50 Ohm Switchable 1uF capacitor Compatible for BCI testing |
| LIN100-1A | Automotive CISPR 25 100Ax1 Path (5μH + 1 Ohm) || 50 Ohm Switchable 1uF capacitor Compatible for BCI testing |
| LIN200-1A | Automotive CISPR 25 200Ax1 Path (5μH + 1 Ohm) || 50 Ohm Switchable 1uF capacitor Compatible for BCI testing |
| LIN400-1A | Automotive CISPR 25 400Ax1 Path (5μH + 1 Ohm) || 50 Ohm Switchable 1uF capacitor Compatible for BCI testing |
| LIN800-1A | Automotive CISPR 25 800Ax1 Path (5μH + 1 Ohm) || 50 Ohm Switchable 1uF capacitor Compatible for BCI testing |
| LIN1500-1A | Automotive CISPR 25 1500Ax1 Path (5μH + 1 Ohm) || 50 Ohm Switchable 1uF capacitor Compatible for BCI testing |
| LIN50-1D | CISPR25, DO-160 5uH || 50Ohm 50Ax1 Path with 10uF feed through |
| LIN100-1D | CISPR 25, DO-160, 5uH || 50Ohm 100Ax1 Path with 10uF feed through |
| LIN200-1D | CISPR 25, DO-160, 5uH || 50Ohm 200Ax1 Path with 10uF feed through |
| LIN400-1D | CISPR 25, DO-160, 5uH || 50Ohm 400Ax1 Path with 10uF feed through |
| LIN800-1D | CISPR 25, DO-160, 5uH || 50Ohm 800Ax1 Path with 10uF feed through |
| LIN50-1A-HV | Automotive CISPR 25, 50Ax1 Path, 0.1 – 110MHz, 5 μH || 50 , DC:1500V AC: 750V 50/60 HzSutaible for BCI with external dummy load |
| LIN100-1A-HV | Automotive CISPR 25, 100Ax1 Path, 0.1– 110MHz, 5 μH || 50 , DC:1500V AC: 750V 50/60 HzSutaible for BCI with external dummy load |
| LIN200-1A-HV | Automotive CISPR 25, 200Ax1 Path, 0.1– 110MHz, 5 μH || 50 , DC:1500V AC: 750V 50/60 HzSutaible for BCI with external dummy load |
| LIN400-1A-HV | Automotive CISPR 25, 400Ax1 Path, 0.1– 110MHz, 5 μH || 50 , DC:1500V AC: 750V 50/60 HzSutaible for BCI with external dummy load |
| LIN800-1A-HV | Automotive CISPR 25, 800Ax1 Path, 0.1– 110MHz, 5 μH || 50 , DC:1500V AC: 750V 50/60 HzSutaible for BCI with external dummy load |
| LIN1500-1A-HV | Automotive CISPR 25, 1500Ax1 Path, 0.1– 110MHz, 5 μH || 50 , DC:1500V AC: 750V 50/60 HzSutaible for BCI with external dummy load |
| Options | |
| REMOTE-EMIRX | Remote Control for EMI Rx with cable Support for R&S, Keysight, Gauss and PMM receivers (receiver make and model to be specified at the time of order) |
| HV1000DC-750AC | Option HV: High voltage 1000V DC & 750V ACNote: Available only with wing terminals |
| HV250-400 | Option 400Hz-HV: 400 Hz 250V High power resistors for single line LISNs. Note: Size increase. |
| F-CAL-PATH | Factory Calibration cost per path |
| CAL-ADAPT-2 | Calibration adaptor for 2 path LISN |
| CAL-ADAPT-4 | Calibration adaptor for 4 path LISN |
| CAL-ADAPT-SINGLE | Calibration adaptor for single line LISN |
| CAL-ADAPT-AUT | Calibration adaptor for Automotive LISN |
| IN60 | IN60 Transient Limiter 10dB insertion loss 9kHz-200MHz |
| IN61 | IN61 Transient Limiter 20dB insertion loss 9kHz-200MHz |
| TERM-50-2W | External 50 Ohm termination 2W DC-1GHz |
| TERM-50-25W | External 50 Ohm termination 25 W DC-1GHz |
| ACC-CAL-2-CISPR | Accredited calibration for 2 line CPSR 16 LISN up to 30 MHz (Note: From a third paty lab. Add 3 weeks for delivery) |
| ACC-CAL-4-CISPR | Accredited calibration for 4 line CPSR 16 LISN up to 30 MHz (Note: From a third paty lab. Add 3 weeks for delivery) |
| ACC-CAL-1-SINGLE | Accredited calibration for single line MIL LISN up to 30 MHz (Note: From a third paty lab. Add 3 weeks for delivery) |
| ACC-CAL-1-AUT | Accredited calibration for single line Automotive LISN up to 108 MHz (Note: From a third paty lab. Add 3 weeks for delivery) |
Pricing: The pricing of LISNs differs in this range: $700-$7000, excluding shipping costs and local taxes.
LIN10-2 (CISPR16 10Ax2 Path) is the lowest priced LISN of the above list. LIN400-4 (CISPR16 400Ax4Path) is the highest priced one. The pricing changes in time and you will see exact pricing on your quote. The prices mentioned here are informational.
FREQUENTLY ASKED QUESTIONS?
1) Will the calibration certificate be delivered with the LISNs? Is there any additional cost?
Yes, with each LISN, manufacturer calibration report will be provided, free of charge. Accredited calibration reports have additional fees as mentioned on above price list. If you need accredited calibration certificates, please choose the appropriate accredited calibration options (ACC-CAL-2-CISPR, ACC-CAL-4-CISPR, ACC-CAL-1-SINGLE, ACC-CAL-1-AUT)
5) What is the maximum temperature limit of the LISNs?
LISN can safely withstand up to 140°C. Sufficient cooling around LISN has to maintained.
6) How temperature of LISNs increase by current?
During continuous operation at 400A, temperature will reach at approximately 135-140°C within six(6) minutes. At 300A continuous operation, temperature will reach at the same level within fifteen(15) minutes.
7) Datasheet of LIN400-1M mentions the LISN can operate at 440 Hz AC voltage. Can the LISN also operate at 115VAC(rms) 400 Hz voltage?
Yes. LIN400-1M can operate with a supply voltage of 115VAC(rms) 400 Hz voltage.
8) Is LIN32-4 fully compliant with CISPR 16-1-2 for both single phase, three phase(4-wire) and DC measurements?
Yes, fully compliant.
9) What are the Standard/Default Accessories that comes with LISNs?
50Ω, 2W Termination, N to N Cable 2 m, N to BNC Adapter and Manufacturer’s Calibration Certificate are standard accessories that comes with every LISN you order. Additional fee is not charged for these items, they will be inside the shipped box.
10) Does 50 ohm 2W termination resistors come with the LISNs and calibration report from you?
Yes. With every LISN, one(1) piece of 50 ohm, 2W termination is delivered. If you need more, we can add it to your quotation and supply.
11) Why 50 ohm 2W termination resistors needed?
When mains power goes to EUT through LISN during radiated emission and immunity testing, LISN RF output port is than terminated with this 50 Ohm termination. You do not need termination for conducted emissions tests since RF output port is connected to the receiver.
12) Why N to N Cable 2 m that comes with every LISN needed?
It is needed to make connection between LISN and receiver. Ensure that your receiver has an N-type RF input port or have additional RF adapter/connector that fits to your reciver’s RF input port.
13) Why N to BNC adapter that comes with every LISN needed?
It is used when LISN is ordered with BNC connector on it, then a BNC-BNC cable is coming with the LISN and sometimes customer needs to use this LISN with a measuring instrument with N port.
14) Are CEE sockets on LISNs available?
Yes, LISNs with CEE sockets are available. Before ordering you should ask CEE sockets. Standard Input and Output terminals provided are CEE Sockets up to 100A, however optional wing terminal and SUPERCON connectors can be ordered.
15) What is the maximum RF power limit of the 20dB Transient Limiter/Attenuator (Model: IN61)?
Max power rating is 2W. For emission measurement, this rating is enough. This not a simple attenuator but transient limiter which will protect input stage of measuring instrument from sudden transients from mains (clipping level up to 100 dBuV)
16) What are the Optional Accessories that may come with LISNs with additional fees?
These are additional and paid four options: Remote Control (built-in) for R&S, Keysight, PMM, Gauss and other EMI Analyzers, High Voltage (built-in) with Wing Terminals, Switch selectable 250 uH Pre-filter (built-in), Calibration Report traceable to ISO 17025. If you would like to order any of these options, please send us your receiver’s model, and the requirement for each option.
16) When ‘REMOTE-EMIRX Remote Control (built-in)’ option is used?
To able to control LISN via measurement receiver or its software. The remote control option makes the LISN controllable and measured line is switchable by the receiver for automated testing. This option is available for receivers manufactured by Rohde&Schwarz, Keysight, PMM, Gauss and other EMI Analyzer/Receiver manufacturers in the market.
17) Which EMI Reciver models are compatible for ‘REMOTE-EMIRX Remote Control (built-in)’ option?
Send us your model and let us review whether your receiver is compatible. If your receiver is compatible, suitable connector will be added to your LISN. When you connect remote control cable between the LISN and the receiver, your receiver will start to control LISN’s line switches. Some model are compatible and some are not for this feaure. For instance, R&S ESR series EMI Receivers are compatible with this LISN remote control option. Some obsolute models are not compatible with the option. For instance, R&S ESVP-3 is outdated/obsoleted model, it can not be used for remote control of LISN.
18) What is the requirement of ‘High Voltage 1 kV DC / 750 Vac (built-in) with Wing Terminals’ HV1000DC-750AC option?
This option is only available with Wing Terminals not with CEE or Schuko socket.
19) What is the price of ‘Switch selectable 250 uH Pre-filter (built-in)’ option?
Its price is 780 USD.
20) Does the transient limiters (Model: IN60 and IN61) have a calibration certificate?
Yes, with each transient limiter, manufacturer calibration report will be provided, free of charge.
21) What are the additional pricing for accredited calibration certificates?
Accredited calibration prices depends on the calibration laboratory and the model calibrated. Current prices are approximately $ 1,100.00 per LISN, and $ 280.00 per transient limiter. When you ask accredited calibration, exact amounts will be on your quotation.
22) How can I pay to purchase a LISN or transient limiter?
You have three options: bank transfer to our bank account, credit card by using our payment link or PayPal.
22) What are the payment terms?
For first and second purchase orders: %100 Advance, together with Purchase Order.
For second and third purchase orders: %50 Advance together with Purchase Order, %50 NET 7 DAYS after delivery.
For fifth and following purchase orders: %0 Advance, %100 NET 30 DAYS after delivery.
23) Do you apply any discount for universities?
Yes, we can apply a 5% education discount on all products except accessories.
24) Are you also able to offer any other RF accessories which are not listed above?
Yes, we are able to offer any RF accessories.
25) Can your LISNs be controlled with our Spectrum Analyzers?
No. Most spectrum analyzers do not have TTL signals to control LISNs. This capablity is usually avaliable with EMI receivers. This option is avaliable for EMI receivers.
26) How many RF outputs LISNs have? Can we ask you to add much more RF output ports on LISN?
The standard LISNs have only one (1) RF measurement port which can be changed from each line at a time and also cover neutral.
If you want to add and seperate RF ports for each channel, yes this paid option is available. Additional cost of $250 is added to make the 4-line LISN with 4 RF outputs. This option is typically used by customers who would like to perform common mode and differential mode analysis.
27) Is the 250 μH pre filter of a CISPR 16 compliant LISN is selectable manually or is it connected all the time?
The standard LISN units have this pre filter connected at all times. A switch option can be provided with additional cost. For instance, the cost to add a switch for the 250 μH pre filter on LIN32-4 is $350. During ordering any LISN you have to notify us to add this option.
Fulfil your test setup requirements
with CISPR 16, CISPR 25, CISPR 32, CISPR 14-1, CISPR 15 and ISO 7637-2 compliant LISNs, ANs and AMNs
Send us your LISN / AMN / AN requirements by filling this short form:
We are engineers, experts and consultants specialised in electrical product testing and certification.
With our team, laboratory and partner laboratories, we are providing testing and certification services for electrical products. We are partnering with testing laboratories located in USA, Ireland, United Kingdom, Germany, Hungary, Italy, Turkey, China, Brazil and South Africa. We are providing our services worldwide.
We are also collaborating with EMC test equipment and chamber manufacturers to provide turnkey systems and solutions to the businesses. After understanding your current requirements, we are offering best device configurations to fulfil your needs. We are delivering, installing test equipments and anechoic chambers with our partner and expert teams. When required, we are also offering on-site and remote trainings for the devices and chambers we deliver.
Our recent blog posts
ISO 11452-4 Requirements
Test levels, test equipments, test setup requirements of ISO 11452-4.
ECE R10 Certification Guide is updated – Edition 1.6
On 16 December 2023, we updated our ECE R10 Certification Guide. Edition 1.6 is ready to download.How to download ECE R10 Cerfication Guide (Edition 1.6)? Click below button to visit download page of the free guide:We are offering ECE R10 related services, test...
Sample ECE R10 Certificate
Example ECE R10 certificate issued for an electronic sub assembly or component used in automotive. Check this sample certificate to understand the final delivered document showing the compliance of the product (type). ECE TYPE-APPROVAL CERTIFICATE issued by NSAI Ireland.
info@testups.com